How to install a garage door opener | Home Improvement Journal

When installing a garage door opener is a project directly, the installation process is very specific manufacturer fully covered here. This article provides an overview of the process, both in preparation for installing a garage door opener or to help you decide whether to install the opener itself.

The methods described in this document are based on the instructions given by Stanley door systems. The method of installing third party ?may vary. When installing a garage door opener, always consult the manufacturer for detailed, step-by-step procedures and follow them closely.

There are three main types of garage door openers:

Persuaded Chain

Belt Driven

Persuaded thread

This article covers installation for the first game of a trip chain. The most important consideration when installing a garage door opener safety.

Safety Precautions

Before installation ? Make sure the garage door is well lubricated and functioning properly. Heavy garage doors are supported by door springs, cables and pulleys not the opener. If you raise and lower the door normally by hand, do not install the door opener until repaired.

Never modify or remove the door of the optical cable, or pulleys. Doors with torsion springs (single coil above the door) should only be repaired by a qualified service technician.

Remove all ropes and cables connected to the garage door to not get caught in it during installation.

Disable or remove all locks of existing garage doors, lest they accidentally attack and destroy both the opening and cause damage.

Do not wear rings, watches or loose clothing while installing or serves or garage door opener.

Ratification of lightweight fiberglass or metal garage door before installing opener to avoid damage to the door and ensure the safety reverse system works correctly.

During installation ? Install the unit high power high enough that people will not work on it, at least 7 ?from the ground if possible.

Garage door openers have a manual disconnect the cable should be fixed about 6 feet from the floor so that adults can do.

If you need to install permanent electrical wiring, always disconnect the power from the main breaker box before attempting to connect the cables. Always connect the power cord from the garage door opener to a properly grounded electrical outlet to avoid electrical shock.

Install the push button controls the 5 ?of the word so that small children can not reach and where the operation can easily see the garage door.

Always set the safety reversal system right and the electric eye system. Referring to the manufacturer?s instructions opener for details.

After installation ? Do not allow children to operate or play with the opener. Keep a radio transmitter in a place not accessible to children.

Do not go under the garage door moves.

Operate the door only when visible, and no obstructions.

Check the safety reverse system and electric eye once a month, and reset if necessary. Periodically check the manual operation of the door.

If possible, use the manual release only when the door is fully closed. Opener not bear the weight of the door, and if the spring is weak or broken, releasing the door can cause falls.

Always disconnect power to the opener while serving a drive or work near the travel chain or other moving parts.

Any damage to any part of the opening, do not use until repaired by a qualified service technician. No rush to the door when the security system is malfunctioning.

Install the lever

Before installing a garage door opener, familiarize yourself with the mounting hardware. To install a garage door opener, insert the tube power units. Slide-pipe itself, then mount the idler end of the tube assembly. Place the same as specified in the manufacturer?s instructions.

Attach the chain to the loop, the traveler around with sprocket and idler, and then back to the van to the other side.

Click the image to view animation.

Therefore connect the chain then traverse drive sprocket power transmission throughout the idler assembly, and is returned at the end traveler. Travelers should be placed according to the manufacturer?s specifications, and the chain should be tight.

Install tensioner assembly to header bracket above the garage door to each manufacturer?s instructions. Find the center of the garage door, and head mounting bracket over time, at a specified distance above the door. Connecting assembly with idler bracket power unit sitting on the floor. Raise the power unit high enough to clear the door when it is open, and put them on the stairs or other proposals.

Lift door to the fully open position, and adjust the height of the plate feed unit or other wedges, so that a certain distance above the door.

Installing energy units 2?4 was among the bare ceiling bracket.

Connect the power supply of the roof with steel angles and mounting straps provided. If ceiling joists are parallel to the door, nail 2x4s between the two beams and attach the power unit for it. Otherwise, fixed directly to the beam.

If the garage ceiling is finished, press three 1?6 rafters and mount the power unit for it.

If the finished ceiling (usually drywall), set the 1?6 ceiling beams and drywall screws.

Connecting opening

When the power is on, open and close the garage door manually to ensure the door free path. Edge must be transparent tube with a distance specified by the manufacturer (usually 1 ?). Be careful not to hit the tourist to lift the door.

Traveler?s tip Linking connecting door. It contains a link to the doors of the bar, Ly link support.

Place the assembly in relation to the traveler (hinge joint consists of a straight link bar, link, and the gate-shaped bracket L). Pull off the cable to remove the door from opening.

Center the door bracket on the garage door, positioned as specified in the installation instructions.

Secure the door bracket centered on the door. The central support (where the L-link attached) determined by the manufacturer inside the door usually from 3 ?to 6?.

Light garage doors should be reinforced with angle iron to avoid damage to the door and allow safety reverse system to function properly.

At the door of steel or fiberglass hardened, install the angle brackets to strengthen and accelerate the door in the corner. Remove the original key of the door.

Monte control button in a convenient location in the garage wall 5 ?of the ground and easy view of the door. Run the wire through the wall and the roof button on the power unit, bound with electrical wire staples. Be careful not to staple through the cable. Connect the power cord to the unit.

Cement pl and configuration electric eye system is essential for maximum safety and proper operation. Follow the manufacturer?s instructions carefully installed. If in doubt, consult your manual with the owner of a phone number or Web site for more information.

If necessary, install an electrical outlet in the ceiling near the power unit and run the power. Always turn off the fuse box before working on the electrical circuit, and observe all safety procedures associated with electrical work.

The outlet must be properly grounded. If you dont know how to install power outlets, allowing electrical contact.

Again relate to the opening of the door. Adjust the safety reverse system according to the manufacturer?s instructions, and then adjust the position of an open door.

For added security, especially around children and pets, federal law requires all installed electric eye garage door opener. This action will close your eyes the door to reverse if someone or something to pass between sensor.

Posts related to How to install a garage door opener

Source: http://lipidejournal.com/2013/01/how-to-install-a-garage-door-opener.html

eric johnson big east tournament ashley olsen new apple tv sun flare love hewitt new ipad